Watch winder settings guide
An automatic watch winds itself as you wear it. Off the wrist, a watch winder keeps it turning so it is ready when you are. Two settings matter: the direction of rotation and the number of turns per day.
The two settings
Direction of rotation. A winder can turn clockwise, anticlockwise, or alternate between the two. Most modern automatic movements wind whichever way the watch turns. Some wind in one direction only: turned the other way, the rotor spins freely and the mainspring gains nothing.
Turns per day (TPD). This is the number of full turns the winder makes in 24 hours, spread across the day with rest periods in between. Most automatic watches stay wound on 650 to 800 turns per day.
The quick answer
- Start with both directions at 650 turns per day. This suits most modern automatic watches.
- Check the watch after 48 hours. If it has stopped or lost time, move up one setting.
- Keep the lowest setting that keeps your watch running. An automatic watch has a slipping clutch, so a winder cannot overwind it, but turns it does not need only add wear.
If your watch winds in one direction only, choose that direction. On a programme that alternates, only half of the turns wind such a watch, so it needs about twice as many.
All settings by brand
Watch brands rarely publish winder settings. The figures below are the starting points listed in watch winder reference tables, checked against the winding direction published by the watch brand or the movement maker wherever one exists. Where the reference tables differ, we give the range.
- Go by the calibre, not the model name. Two watches with the same name can carry different movements.
- "Either direction" means clockwise, anticlockwise and alternating all wind the watch.
- Directions are given facing the dial.
Rolex
Tudor
Omega
Breitling
TAG Heuer
Cartier
IWC
Panerai
Patek Philippe
Audemars Piguet
Jaeger-LeCoultre
Zenith
Longines
Tissot and Hamilton
Oris
Seiko and Grand Seiko
Citizen and other Miyota-powered watches
Other brands, by movement
* Reference tables differ on this movement: either direction, or anticlockwise at 800. If your watch runs down on a programme that alternates, switch to anticlockwise at 800.
† This is the figure Oris publishes for these calibres: 10 hours of winding, then 14 hours of rest. Few winders reach it. Use the highest anticlockwise setting and top up with the crown if needed.
Same name, different movement. Older versions and chronograph versions of a model often carry another movement. Some Omega Speedmaster, Cartier, Breitling, TAG Heuer and IWC models wind clockwise only, and a few Patek Philippe calibres wind clockwise instead of anticlockwise. If your calibre is not in the table, use the quick answer above or ask us.
Watches that should not go on a winder
- Hand-wound watches. There is no rotor, so a winder cannot wind them. Examples: Omega Speedmaster Moonwatch Professional, Panerai Luminor Base Logo (calibre P.6000) and Luminor Marina 8 Days (calibre P.5000), Jaeger-LeCoultre Reverso Tribute Monoface (calibre 822), Patek Philippe Calatrava 6119.
- Quartz and solar watches. They run on a battery or on light.
- Seiko Kinetic. It charges a cell instead of winding a spring, and a winder is not recommended for charging it.
Grand Seiko Spring Drive is different: it has a mainspring wound by a rotor, so a winder works.
Setting your Hourstead winder
The table gives you a direction and a number of turns per day. How you set them depends on the winder.
Regent: set by turns per day. The control panel sets the direction (clockwise, anticlockwise or alternating) and the turns per day: 650, 750, 850, 1,000 or 1,950. Use the table as it is. Where it gives a range, start with the lower figure.
Other winders: set by programme. These winders turn for a few minutes, rest, then turn again. Each programme has its own direction and rhythm, so the programme fixes the number of turns. Take the direction from the table and choose the programme that matches.
For any other model, the instructions supplied with your winder list its programmes. You can also ask us.
Which programme for your watch
- Either direction: any programme winds the watch. The alternating one is the usual choice.
- Clockwise only or anticlockwise only: use the programme that turns that way. Regent, Archive, Chamber Noir and Form Slate have both. Nomad has clockwise.
- On a winder that only alternates, half of the turns wind a one-direction watch. If the watch slows or stops within 48 hours, it needs a winder with a programme in its direction.
- A programme can give more turns than the figure in the table. That does not overwind the watch. Where your winder has several rhythms, keep the one with the longest rest that keeps your watch running.
How to find your calibre
- Look at the caseback, the warranty card or the instruction booklet. The calibre or the reference number is usually printed there.
- Search the reference number on the watch brand's website to find the calibre.
- Still unsure? Ask your watchmaker, or contact us and we will help you choose a setting.
Brand, model and calibre names are used for reference only and are trademarks of their respective owners. Hourstead is not affiliated with these brands. This guide is for information: your watch manufacturer's instructions take priority.